Quick-fuel-technology 701-1BD BLACK DIAMOND INTAKE MANIFOLD SMALL BLOCK Manuel d'utilisateur télécharger pdf

QUICK FUEL TECHNOLOGY®

BLACK DIAMOND® INTAKE MANIFOLD P/N 701-1BD

SMALL BLOCK CHEVROLET

INTAKE MANIFOLD

INSTALLATION INSTRUCTIONS

APPLICATIONS:

The P/N 701-1BD BLACK DIAMOND® intake manifold is designed for square-bore carburetor applications on 1957-86

262-400cid Small Block Chevrolet engines and SBC engines equipped with 1987-91 L98 aluminum Corvette cylinder heads

(non-EGR applications). Also, this manifold will work with any SBC engine equipped with aftermarket cylinder heads, as long as

they have a standard port flange opening and bolt hole locations.

This 180° dual plane intake manifold is designed to provide the best performance for stock to street-performance engine

applications to a maximum engine speed of 5500 RPM. The carburetor-mounting pad is designed to accept all stock or

aftermarket square-bore carburetors with manual or electric chokes. BLACK DIAMOND® intake manifolds are designed to

accept most stock hardware, such as coolant and vacuum lines, coils, HEI distributors, and brackets. Few alterations, if any,

should be required.

EMISSIONS EQUIPMENT:

P/N 701-1BD does not accept an EGR valve, hot-air, or divorced chokes. This part is not legal for sale or use for motor

vehicles with pollution-controlled equipment.

BEFORE YOU BEGIN INSTALLATION:

The following installation instructions must be carefully read and understood before you begin installation. Below is a

preliminary check list that should be completed before you begin installation. Improper application or installation of this product

may result in unsatisfactory performance, fuel mileage, or emissions. Failure to follow these installation instructions could result

in engine damage and may void your warranty. If you require any assistance regarding this product please contact Quick Fuel

Technology® Technical Support at: 270-793-0900, Fax: 270-793-0951, or for online assistance refer to our website at

www.quickfueltechnology.com.

PRELIMINARY CHECKLIST:

 Carefully read and understand these installation instructions.

 Check that this intake manifold is the correct choice for your engine application, desired performance level, and local

emissions laws. This intake manifold will require a manual or electric carburetor choke.

 Inspect the manifold for any damage that may have occurred during shipping. If damaged, contact your dealer immediately.

 Check that all of the parts listed in the Kit Contents list in these instructions have been included with your intake manifold.

 Inspect all threaded holes.

 Inspect all internal passages with a light and a stiff wire to be sure that the passages are not obstructed and have

been properly cleaned to be free of any debris.

 Check for sufficient hood clearance with this intake manifold and intended carburetor/air cleaner combination to be used.

 Check that you have all of the parts required for the installation. These include the intake manifold gasket set, gasket

adhesive, RTV silicone sealant, and pipe thread sealant as shown in the Parts Required list in these installation instructions.

 Check that you have all the tools you will need to perform the intake manifold installation. A recommended but not

exhaustive list is located in these installation instructions.

 Check that you have the proper intake manifold fasteners for this application.

 If using your old carburetor, before you remove it from the engine make sure it is working properly and that the carburetor is

tuned properly. Consult the shop manual or installation instructions for that carburetor to determine if the carburetor is in

proper tune.

1 2 3 4 5

Résumé du contenu

Page 1 - SMALL BLOCK CHEVROLET

QUICK FUEL TECHNOLOGY® BLACK DIAMOND® INTAKE MANIFOLD P/N 701-1BD SMALL BLOCK CHEVROLET INTAKE MANIFOLD INSTALLATION INSTRUCTIONS APPLICATIONS:

Page 2 - INSTALLATION INSTRUCTIONS:

2  If you are using a new carburetor, make sure you have read and understand the installation instructions for that carburetor and that the initial

Page 3 - MANIFOLD REMOVAL PROCEDURE:

3 CHECK FOR ADEQUATE HOOD HEIGHT: 1. We recommend making several columns of modeling clay and placing them on your air cleaner in various positions

Page 4

4 4. When you are fully prepared to install the intake manifold, apply a 1/4” wide bead of oil-resistant RTV-silicone sealant to the front and rear

Page 5 - 99-701-1BD

5 CAUTION! Check to be sure that there is adequate clearance for the throttle and choke linkages through their full range of travel. IMPORTANT: Ch

Commentaires sur ces manuels

Pas de commentaire

Quick-fuel-technology 701-1BD BLACK DIAMOND INTAKE MANIFOLD SMALL BLOCK Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Quick-fuel-technology 701-1BD BLACK DIAMOND INTAKE MANIFOLD SMALL BLOCK . Quick Fuel Technology 701-1BD BLACK DIAMOND INTAKE MANIFOLD SMALL BLOCK CHEVROLET User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Quick-fuel-technology 701-1BD BLACK DIAMOND INTAKE MANIFOLD SMALL BLOCK